This week we'll complete our initial discussion of Opens & Shorts in electrical circuits. We'll use some of the concepts developed over the past couple of weeks to figure out how to use a DMM to find opens & shorts in circuits.
There will be a demonstration of what happens in an electrical circuit under the conditions of an open circuit and a short circuit. Using the calculations in class, we determined that under normal operation, PR1 = Power dissipated by R1 is 0.364 Watts and PR2 = 0.017 Watts. Since both resistors had a power rating of 0.5 watts, they should both easily handle normal conditions.
When an open is created, the current becomes zero (stops) and all of the voltage will appear across the open. The resistors will have no voltage across them . According to Ohm's Law, V=I*R, so if I=0, the Voltage, V, will be zero as well. Our measurements in class confirmed this. The resistors, because they had no voltage across them or current through them, were not dissipating any power. Therefore, there was no risk of damage to the resistors.
When a short circuit is created across the 1000 ohm resistor, the total circuit resistance of the circuit dropped (to 47 ohms) causing the total current to increase dramatically. In the demonstration the current jumped to about 0.4 Amps, more than 21 times the normal current. All 20 volts of the DC supply show up across the 47 ohm resistor since there are 0 volts across the short & R1. Therefore, the power dissipated by R2 is now about 8.5 Watts. This is about 17 times it's rated power dissipation. As seen in the class demo, the resistor gets hot, begins to discolor, emits a bit of smoke, continues to heat up with further discoloration and smoke, and eventually the resistor will glow and obviously burn. When allowed to do this to completion, the current through the circuit ultimately became near 0, and when measured afterward, the 47 ohm resistor measured in at 100's of thousands of ohms. The characteristic odor of the burnt component was also indicative of the failure due to the short.
Week #8: (10/25) Opens & Short, Conclusion.
-
- Posts: 2383
- Joined: Fri Sep 04, 2015 6:59 pm
Return to “EET-106 Troubleshooting (Fridays)”
Jump to
- Electronics Systems - General Information
- ↳ Instructor Information
- ↳ Career Related Links and Information
- ↳ Career Information (General)
- ↳ Interviewing Skills
- 2024 Spring
- ↳ EET-250 Control Systems
- ↳ EET-250 Lecture
- ↳ EET-250 Lab
- ↳ EET-255 Advanced Topics in E.E.T./Automation
- ↳ EET-260 Microprocessor Applications
- ↳ EET-260 Lecture
- ↳ EET-260 Lab
- ↳ EET-265 Advanced Automation
- ↳ EET-265 Lecture
- ↳ EET-265 Lab
- ↳ Information for All Students
- ↳ Progress Reports for Sorting Group
- ↳ Progress Reports for Vending Group
- ↳ Progress Reports for HVAC Group
- Previous Semesters
- ↳ 2023 Fall
- ↳ EET-101 PCs, Programming & Robots
- ↳ EET-101 Lecture
- ↳ EET-101 Lab
- ↳ EET-120 Fluid Power Technology
- ↳ EET-200 Solid State Electronics
- ↳ EET-200 Lecture
- ↳ EET-200 Lab
- ↳ EET-210 Digital and Linear Circuits
- ↳ EET-210 Lecture
- ↳ EET-210 Lab
- ↳ 2023 Spring
- ↳ EET-250 Control Systems
- ↳ EET-250 Lecture
- ↳ EET-250 Lab
- ↳ EET-255 Advanced Topics in E.E.T./Automation
- ↳ EET-260 Microprocessor Applications
- ↳ EET-260 Lecture
- ↳ EET-260 Lab
- ↳ EET-265 Advanced Automation
- ↳ EET-265 Lecture
- ↳ EET-265 Lab
- ↳ Progress Reports for Golfball Group
- ↳ Progress Reports for Car Assembly
- ↳ Lab Information for All Students
- ↳ 2022 Fall
- ↳ EET-101 PCs, Programming & Robots
- ↳ EET-101 Lecture
- ↳ EET-101 Lab
- ↳ EET-120 Fluid Power Technology
- ↳ EET-200 Solid State Electonics
- ↳ EET-200 Lecture
- ↳ EET-200 Lab
- ↳ EET-210 Digital and Linear Circuits
- ↳ EET-210 Lecture
- ↳ EET-210 Lab
- ↳ EET-235L-D03 PLCs 2 Lab
- ↳ 2022 Spring
- ↳ EET-250 Control Systems
- ↳ EET-250 Lecture
- ↳ EET-250 Lab
- ↳ EET-255 Advanced Topics in E.E.T./Automation
- ↳ EET-260 Microprocessor Applications
- ↳ EET-260 Lecture
- ↳ EET-260 Lab
- ↳ EET-265 Advanced Automation
- ↳ EET-265 Lecture
- ↳ EET-265 Lab
- ↳ Lab Information for All Students
- ↳ Automated Greenhouse - Weekly Progress Reports (Individual)
- ↳ 2021 Fall
- ↳ EET-101 PCs, Programming & Robots
- ↳ EET-101 Lecture
- ↳ EET-101 Lab
- ↳ EET-120 Fluid Power Technology
- ↳ EET-200 Solid State Electronics
- ↳ EET-200 Lecture
- ↳ EET-200 Lab
- ↳ EET-210 Digital and Linear Circuits
- ↳ EET-210 Lecture
- ↳ EET-210 Lab
- ↳ 2021 Spring
- ↳ EET-120 Fluid Power
- ↳ EET-250 Control Systems
- ↳ EET-250 Lecture
- ↳ EET-250 Lab
- ↳ EET-255 Advanced Topics in E.E.T./Automation
- ↳ EET-260 Microprocessor Applications
- ↳ EET-260 Lecture
- ↳ EET-260 Lab
- ↳ EET-265 Advanced Automation
- ↳ EET-265 Lecture
- ↳ EET-265 Lab
- ↳ End of Semester Project Requirements
- ↳ Allen Bradley Information
- ↳ Conveyor Information
- ↳ Dobot Information
- ↳ EP-250 Pneumatic Trainer Info
- ↳ Fanuc Information
- ↳ Keyence SZ-01S Laser Safety Scanner
- ↳ Misc. Knowledge Base
- ↳ Misc. Lab Equipment Documentation
- ↳ Really Old Forums
- ↳ 2020 Fall
- ↳ Linux - General help
- ↳ EET-101 PCs, Programming & Robots
- ↳ EET-101 Lecture
- ↳ EET-101 Lab
- ↳ EET-120 Fluid Power
- ↳ EET-200 Solid State Electonics
- ↳ EET-200 Lecture
- ↳ EET-200 Lab
- ↳ EET-210 Digital and Linear Circuits
- ↳ EET-210 Lecture
- ↳ EET-210 Lab
- ↳ ELE-111L Internet of Things Lab
- ↳ Basic Subnetting
- ↳ 2020 Spring
- ↳ EET-120 Fluid Power
- ↳ EET-240 Robotics & Automation
- ↳ EET-250 Control Systems
- ↳ EET-250 Lecture
- ↳ EET-250 Lab
- ↳ EET-255 Advanced Topics in E.E.T./Automation
- ↳ EET-260 Micro-Processor Applications
- ↳ EET-260 Lecture
- ↳ EET-260 Lab
- ↳ EET-265 Advanced Automation
- ↳ EET-265 Lecture
- ↳ EET-265 Lab
- ↳ Lab Information for All Groups
- ↳ Weekly Progress Reports - Carwash Project
- ↳ Weekly Progress Reports - Filling Project
- ↳ 2019 Fall
- ↳ CSE-110 Information, Reading and Video List
- ↳ CSE-110 - General Information
- ↳ EET-101 PCs, Robots & Programming
- ↳ EET-101 Lecture
- ↳ EET-101 Lab
- ↳ EET-104/5/6 Safety, Diagrams, Troubleshooting
- ↳ EET-104 Safety & Health in Industry (Mondays)
- ↳ EET-105 Technical Diagrams for Automation (Wednesdays)
- ↳ EET-106 Troubleshooting (Fridays)
- ↳ EET-120 Fluid Power
- ↳ EET-200 Solid State Electronics
- ↳ EET-200 Lecture
- ↳ EET-200 Lab
- ↳ EET-210 Digital & Linear Circuits
- ↳ EET-210 Lecture
- ↳ EET-210 Lab
- ↳ EET-250 Control Systems
- ↳ EET-250 Lecture
- ↳ EET-250 Lab
- ↳ EET-260 Micro-Processor Applications
- ↳ EET-260 Lecture
- ↳ EET-260 Lab
- ↳ 2019 Spring
- ↳ EET-101 PC's, Programming & Robots
- ↳ EET-101 Lecture
- ↳ EET-101 Lab
- ↳ EET-120 Fluid Power
- ↳ Fluid Power (Public)
- ↳ EET-210 Digital and Linear Circuits
- ↳ EET-210 Lecture
- ↳ EET-210 Lab
- ↳ EET-235 PLCs 2
- ↳ EET-235 Lecture
- ↳ EET-235 Lab
- ↳ EET-250 Control System Theory
- ↳ EET-250 Lecture
- ↳ EET-250 Lab
- ↳ EET-255 Advanced Topics in E.E.T./Automation
- ↳ EET-260 Microprocessor Applications
- ↳ EET-260 Lecture
- ↳ EET-260 Lab
- ↳ EET-265 Advanced Automation
- ↳ EET-265L Lab - Day
- ↳ Weekly Progress Reports - Cold Beverage Dispenser
- ↳ Weekly Progress Reports - Warehouse Storage/Retrieval
- ↳ EET-265L Lab - Evening
- ↳ ELE-111 Internet of Things
- ↳ ELE-111 General Information
- ↳ ELE-111 Reading List
- ↳ ELE-115L - Bigos
- ↳ General
- ↳ Mech-Elec WFD Training
- ↳ Mech-Elec (Public)
- ↳ Mech-Elec WFD Training -Cohort 2
- ↳ 2018 Fall
- ↳ CSE-110 Intro to Comp (A+)
- ↳ CSE-110 General Information
- ↳ EET-101 PC's, Programming & Robots
- ↳ EET-101 Lecture
- ↳ EET-101 Lab
- ↳ EET-104/105/106 Safety & Health, Tech Diagrams, Troubleshooting
- ↳ EET-104 Safety & Health in Industry
- ↳ EET-105 Technical Diagrams for Automation
- ↳ EET-105 Public
- ↳ EET-106 Developing Troubleshooting Skills
- ↳ EET-200 Solid State Electronics
- ↳ EET-200 Lecture
- ↳ EET-200 Lab
- ↳ EET-210 Digital and Linear Circuits
- ↳ EET-210 Lecture
- ↳ EET-210 Lab
- ↳ 2018 Spring
- ↳ CSE-110L-Intro To Comp
- ↳ CSE-110L General
- ↳ CSE-220 Security Reading List
- ↳ EET-120 Fluid Power Technology
- ↳ EET-120 Fluid Power (Public)
- ↳ EET-250 Control System Theory
- ↳ EET-250 Lecture
- ↳ EET-250 Lab
- ↳ EET-255 Advanced Topics in EET/Automation
- ↳ EET-260 Microprocessor Applications
- ↳ EET-260 Lecture
- ↳ EET-260 Lab
- ↳ EET-265 Advanced Automation
- ↳ EET-265 Lecture
- ↳ EET-265 Lab
- ↳ Weekly Progress Reports - Post Weekly Progress Reports here.
- ↳ 2017 Fall
- ↳ CSE-110 Intro To Computers (A+)
- ↳ CSE-110 Information
- ↳ EET-101 PCs, Programming & Robots
- ↳ EET-101 Lecture
- ↳ EET-101 Lab
- ↳ EET-104/105/106 Safety/Tech. Diagrams/Troubleshooting
- ↳ EET-104 Safety & Health in Industry
- ↳ EET-105 Technical Diagrams for Automation
- ↳ EET-106 Developing Troubleshooting Skills
- ↳ EET-200 Solid State Electronics
- ↳ EET-200 Lecture
- ↳ EET-200 Lab
- ↳ EET-210 Digital and Linear Circuits
- ↳ EET-210 Lecture
- ↳ EET-210 Lab
- ↳ EET-260 Microprocessor Applications
- ↳ EET-260 Lecture
- ↳ EET-260 Lab
- ↳ 2017 Spring
- ↳ General Resouces
- ↳ CSE-110 Intro to Comp
- ↳ CSE-110 Reading List & General Information (Public)
- ↳ CSE-160 Intro To Programming (Python)
- ↳ CSE-240 Resources
- ↳ EET-120 Fluid Power
- ↳ EET-250 Control System Theory
- ↳ EET-250 Lecture
- ↳ EET-250 Lab
- ↳ EET-255 Advanced Topics in E.E.T.
- ↳ EET-255 Lecture (Public)
- ↳ EET-260 Microprocessor Applications
- ↳ EET-260 Lecture
- ↳ EET-260 Lab
- ↳ EET-265 Advanced Automation
- ↳ EET-265 Lecture
- ↳ EET-265 Lab
- ↳ Allen-Bradley Micro820 PLC Info
- ↳ Trail Mix Vending Machine - Evening
- ↳ Progress Reports
- ↳ Support Information
- ↳ Team Fluid Processing - Day
- ↳ Progress Reports
- ↳ Support Information
- ↳ Team Warehouse Stocking/Retrieval - Day
- ↳ Progress Reports
- ↳ Support Information
- ↳ ELE-111 Internet of Things (IOE)
- ↳ General Information
- ↳ 2016 Fall
- ↳ CSE-140 Operating Systems 1
- ↳ General Information
- ↳ CSE-110 Intro To Computer Systems
- ↳ General Information
- ↳ CSE-150 Linux Command Line and Shell Programming
- ↳ General Information
- ↳ CSE-160 Intro To Programming Using Python
- ↳ General Information
- ↳ CSE-220 Computer and Network Security
- ↳ General Information
- ↳ CSO-205 Cisco Scaling Networks
- ↳ EET-101 PCs, Programming & Robots
- ↳ EET-101 Lecture
- ↳ EET-101 Lab
- ↳ EET-104/105/106 Safety, Tech. Diagrams & Troubleshooting
- ↳ EET-104 Safety & Health in Industry
- ↳ EET-105 Reading Technical Diagrams
- ↳ EET-106 Developing Troubleshooting Skills
- ↳ EET-200 Solid State Electronics
- ↳ EET-200 Lecture
- ↳ EET-200 Lab
- ↳ EET-210 Digital and Linear Circuits
- ↳ EET-210 Lecture
- ↳ EET-210 Lab
- ↳ EET-250 Control System Theory
- ↳ EET-250 Lecture
- ↳ EET-250 Lab
- ↳ EET-260 Microprocessor Applications
- ↳ EET-260 Lecture
- ↳ EET-260 Lab
- ↳ ELE-110 Electronics For Techs 1
- ↳ General Information
- ↳ ELE-120 Printed Circuit Design
- ↳ General Information
- ↳ ELE-130 Intro To Project Management
- ↳ General Information
- ↳ ELE-210 Circuit Theory
- ↳ General Information
- ↳ ELE-250 Research and Development
- ↳ General Information
- ↳ 2016 Spring
- ↳ CSE-110 Intro To Computer Systems
- ↳ CSE-110 General Information
- ↳ Linux and Programming
- ↳ CSE-150 Linux and Shell Programming
- ↳ CSE-150 General information
- ↳ CSE-160 Introduction to Programming with Python
- ↳ CSE-160 General
- ↳ CSE-220 Computer and Network Security
- ↳ CSE-220 General Information
- ↳ CSE-240 Operating Systems 2 (Windows 2012 Server)
- ↳ CSE-240 General Information
- ↳ CSE-260 Application Servers
- ↳ CSE-260 General
- ↳ ELE-111 Internet of Everything (IOE)
- ↳ ELE-111 General
- ↳ ELE-115 Electronics for Techs 2
- ↳ ELE-115 General Information
- ↳ ELE-265 Senior Projects
- ↳ EET-120 Fluid Power Technology
- ↳ EET-130 Fundamentals of Motor Controls
- ↳ EET-135 PLCs 1
- ↳ EET-140 Fundamentals of Robotics
- ↳ EET-250 Control System Theory
- ↳ EET-250 Lecture
- ↳ EET-250 Lab
- ↳ EET-255 Advanced Topics in E.E.T.
- ↳ EET-260 Microprocessor Applications
- ↳ EET-260 Lecture
- ↳ EET-260 Lab
- ↳ EET-265 Advanced Automation
- ↳ EET-265 Lecture
- ↳ EET-265 Lab
- ↳ 2015 Fall
- ↳ 2015 Fall
- ↳ CSE-110 Intro to Computer Systems
- ↳ CSE-110 General
- ↳ CSE-140 Operating Systems 1
- ↳ CSE-140 General
- ↳ CSE-150 Linux Command and Shell Programming
- ↳ CSE-150 General
- ↳ CSE-155 Intro to Programming
- ↳ CSE-155 General Information
- ↳ CSE-220 Computer and Network Security
- ↳ CSE-220 General
- ↳ CSO-105 Cisco Networking
- ↳ CSO-105 General
- ↳ CSO-205 Cisco 3 Reading List
- ↳ ELE-111 Internet of Everything
- ↳ ELE-111 General
- ↳ ELE-111 Reading List
- ↳ ELE-121/2/3 Documentation
- ↳ ELE-121/2/3 General
- ↳ ELE-130 Intro to Project Management
- ↳ ELE-130 - General
- ↳ ELE-210 Circuit Theory
- ↳ ELE-210 General
- ↳ ELE-210 Lab (Private)
- ↳ EET-101 PCs, Programming & Robots
- ↳ EET-101 Lecture
- ↳ EET-101 Lab
- ↳ EET-104 Safety & Health in Industry
- ↳ EET-105 Technical Diagrams for Automation
- ↳ EET-106 Developing Troubleshooting Skills
- ↳ EET-120 Fluid Power Technology
- ↳ EET-135 PLCs 1
- ↳ Lecture
- ↳ Lab
- ↳ EET-140 Fundamentals of Robotics
- ↳ Lecture
- ↳ Lab
- ↳ EET-200 Solid State Circuits
- ↳ Lecture
- ↳ Lab
- ↳ EET-210 Digital & Linear Circuits
- ↳ Lecture
- ↳ Lab
- ↳ EET-240 Robotics/Automated Systems
- ↳ Lecture
- ↳ Lab
- ↳ EET-265 Advanced Automation
- ↳ Lecture
- ↳ Lab/Project
- ↳ E-Makers's Club
- ↳ E-Makers General information
- ↳ Meeting schedule and locations.