Page 1 of 1

Week #7: (3/2-6) Parallax Process Control Wk. #2 - Chapter 3

Posted: Fri Feb 21, 2020 7:22 pm
by rjagodowski
Last week, in Week #6, you should've began this last week if you're on schedule. I will spend some time in lecture today going over this content as an introduction.

This week you will begin using the Parallax Process Control kits. The Process Control text and other documentation can be downloaded Week #6.


This week's lab exercise is to continue working in the Process Control text. You should have read and worked through Chapters 1 & 2 at this point. If not, do so FIRST!!!

NOTE: StampPlot software IS NOT currently installed on the computers in our lab. Until then, you need to follow the directions given Week #6 and install it on your own computer or have your professor install it on the computer you are going to use. It is highly recommended that you install it on your own computer as you will be using StampPlot regularly for the rest of this course and creating numerous screenshots and files. Having this installed on your own computer will be very helpful.

As part of this week's exercise in Chapter 3, you must post a screenshot of your StampPlot showing the D.C. LoadLine and Power Dissipation Curve of the Bipolar Transistor. A sample post is included in the Reply below. Be sure to answer all questions in the chapter and you should be able to understand all of the calculations presented.
For your convenience, a pdf of just Chapter 3 is attached here:
Process-Control-Text-CHapter 3_v1.0.pdf
(1.24 MiB) Downloaded 37 times
Be sure to use the right StampPlot macros and BS2 programs for each activity.

Some of the experiments in this chapter and throughout the rest of the text will make use of the ADC0831 Analog-to-Digital Converter chip. Here is the data sheet for this device:
Process-Control-Text-CHapter 3_v1.0.pdf
(1.24 MiB) Downloaded 37 times
ADC0831_SpecSheet.pdf
(2.12 MiB) Downloaded 30 times

Re: Week #7: (3/2-6) Parallax Process Control - Chapter 3- Week #2

Posted: Sat Feb 22, 2020 2:30 pm
by rjagodowski
Your screen shot from the StampPlot software should look similar to the graph below. Post your picture as I did this one.
chapter 3_StampPlotScreenShot.jpg
chapter 3_StampPlotScreenShot.jpg (139.41 KiB) Viewed 439 times

Re: Week #7: (3/2-6) Parallax Process Control Wk. #2 - Chapter 3

Posted: Tue Mar 10, 2020 3:34 pm
by kjbusiere0001
Konnor Busiere
Activity 1
Activity 2
Activity 3
Activity 4
Activity 5

Re: Week #7: (3/2-6) Parallax Process Control Wk. #2 - Chapter 3

Posted: Tue Mar 10, 2020 3:40 pm
by csrichter0001
Conner Richter has completed this lab. Both Conner's worked together for lab.
Picture 1 => Activity 1
Picture 2 => Activity 2
Picture 3 => Activity 3
Picture 4 => Activity 4
Picture 5 => Activity 5

Re: Week #7: (3/2-6) Parallax Process Control Wk. #2 - Chapter 3

Posted: Tue Mar 10, 2020 4:20 pm
by erivera0005
I've completed the lab from Chapter 3.
Activities from # 1 thru # 5

Re: Week #7: (3/2-6) Parallax Process Control Wk. #2 - Chapter 3

Posted: Thu Mar 12, 2020 2:44 pm
by avkaptyug0001
completed week 7

Re: Week #7: (3/2-6) Parallax Process Control Wk. #2 - Chapter 3

Posted: Thu Apr 02, 2020 11:47 am
by vshostak
.