Post your progress, contributions, work and anything else you did for the Team project here.
There will be a separate Topic for each week during the semester.
These are individual posts, so each member must post their own progress report. If you worked with others, or the entire group, then you can mention that in your post as well. But each member must post to receive credit for this week's post.
Week #10 (3/28-4/1) Weekly Progress Report
-
- Posts: 2380
- Joined: Fri Sep 04, 2015 6:59 pm
-
- Posts: 54
- Joined: Fri Sep 25, 2020 10:38 am
Re: Week #10 (3/28-4/1) Weekly Progress Report
Jorge Gonzalez
This week I spent most of the time adding to the PLC program. I finished making the pick and place program and I added a timer for the greenhouse light and pump. Did not get to test it yet because Nick is in the process of wiring everything up and making it look neat so I helped a little bit with that too.
This week I spent most of the time adding to the PLC program. I finished making the pick and place program and I added a timer for the greenhouse light and pump. Did not get to test it yet because Nick is in the process of wiring everything up and making it look neat so I helped a little bit with that too.
-
- Posts: 56
- Joined: Fri Sep 25, 2020 10:16 am
Re: Week #10 (3/28-4/1) Weekly Progress Report
Cole Lozinski
For this week I helped with programing and figuring out what pins we were going to use on the dobot. I also helped with mounting the PLC to a board that we will be using to put all our relays and switches on.
For this week I helped with programing and figuring out what pins we were going to use on the dobot. I also helped with mounting the PLC to a board that we will be using to put all our relays and switches on.
-
- Posts: 37
- Joined: Fri Sep 25, 2020 9:14 am
Re: Week #10 (3/28-4/1) Weekly Progress Report
Finalized the setup of the dobot program and mounted components on the plc Pannel.
-
- Posts: 35
- Joined: Tue Sep 21, 2021 1:00 pm
Re: Week #10 (3/28-4/1) Weekly Progress Report
William Penalo
All week i worked on making the Arduino PH and Temp sensors both calibrated, working and displaying with analog outputs to be able to be added on to the PLC. The PH sensor had to be recalibrated to be able to read correctly as its output would vary to much but by Thursday it seemed to had finally stabilized in the correct readings
All week i worked on making the Arduino PH and Temp sensors both calibrated, working and displaying with analog outputs to be able to be added on to the PLC. The PH sensor had to be recalibrated to be able to read correctly as its output would vary to much but by Thursday it seemed to had finally stabilized in the correct readings
-
- Posts: 58
- Joined: Fri Sep 25, 2020 10:35 am
Re: Week #10 (3/28-4/1) Weekly Progress Report
Wiring up electrical cabinet
Re: Week #10 (3/28-4/1) Weekly Progress Report
work with nike to wire the PLC in the board and got all the input and output working ready for the devisees
-
- Posts: 47
- Joined: Tue Sep 14, 2021 7:00 pm
Re: Week #10 (3/28-4/1) Weekly Progress Report
I figured out exactly where I wanted to connect wires to and began soldering them in place.
-
- Posts: 15
- Joined: Tue Mar 31, 2020 11:02 am
Re: Week #10 (3/28-4/1) Weekly Progress Report
The PH sensor had to be recalibrated to be able to read correctly as its output would vary to much but by Thursday it seemed to had finally stabilized in the correct readings working and displaying with analog outputs to be able to be added on to the PLC