Week #15: (4/29-5/3) Progress Reports, Inductive Prox Sensor

Post Reply
rjagodowski
Posts: 1642
Joined: Fri Sep 04, 2015 6:59 pm

Week #15: (4/29-5/3) Progress Reports, Inductive Prox Sensor

Post by rjagodowski »

Post your progress reports in the form of a reply to this Topic.

Here's the datasheet for the inductive proximity sensor used for the homing circuit on the stepper motor drive:
LJ12A3-4-Z_InductiveProx_32086hd.pdf
(52.7 KiB) Downloaded 26 times

Some links about barcodes and the Raspberri Pi.

Link 1, simple program

Link 2, simple program

Link 3, more stuff.
dasubbotin
Posts: 32
Joined: Tue Sep 12, 2017 6:03 pm

Re: Week #15: (4/29-5/3) Progress Reports.

Post by dasubbotin »

Not sure where my first post went, but here's the second one.
This was our second class this week, on April 24.
Today, Vinny installed Panduit on the backpanel, which made the wiring look very organized and nice. A front panel was then mounted along with a makeshift belt tensioner that worked well. We measured the ice cube dimensions at 1.25" x 1.375". Rob tried to program and understand how to get a program a motion block in the PLC logic for the 850, to no avail. I tried to research and look for additional sample code or pointers online, to which I did not find much.
dasubbotin
Posts: 32
Joined: Tue Sep 12, 2017 6:03 pm

Re: Week #15: (4/29-5/3) Progress Reports, Inductive Prox Sensor

Post by dasubbotin »

Today, more good progress was made. Vinnie had installed output relays overnight.
Most importantly Rob with Dave's help got the Motion Block working figured out. Now we need to program relative motion and figure out the assigned positions that will be needed for the cup positions. Ricky and Michelle have the robot pretty much ready to as soon as we have the relative positions we need.
We collected a list of the the I/Os so that we can start writing the program for how the system will flow as a whole. Troubleshooting was needed for some time to figure out how to get the homing sensor wired correctly.
rlafleche0001
Posts: 5
Joined: Wed Jan 30, 2019 8:14 pm

Re: Week #15: (4/29-5/3) Progress Reports, Inductive Prox Sensor

Post by rlafleche0001 »

Here is the excel file for the micro850 inputs and outputs..

Word document.. might help
Copy of the motion block working, Power up instruction with reset, Homing instruction, and move relative instruction.
Attachments
micro850_Test_5_1_19_Motion_working.rar
(1.33 MiB) Downloaded 26 times
Motion_block_pictures.png
Motion_block_pictures.png (187.87 KiB) Viewed 419 times
Motion_block_pictures_1.png
Motion_block_pictures_1.png (72.18 KiB) Viewed 419 times
Micro850IO.xlsx
(11.66 KiB) Downloaded 25 times
dasubbotin
Posts: 32
Joined: Tue Sep 12, 2017 6:03 pm

Re: Week #15: (4/29-5/3) Progress Reports, Inductive Prox Sensor

Post by dasubbotin »

A couple of us came in on the off-day, Thusday night to play with Raspberry Pi and get a barcode scanner working.
It was interesting to see and learn about what this little compute is and what it is capable of, how it is its own computer with it's own operating system and applications. We cannibalized an online program that compared two scanner imputs and decided if they matched. The intention was to get this working and then modify it into our desired feature of comparing a scan to a stored value in a database. However, it was challenging enough getting the program to run without a deeper knowledge of linux, not too mention, it was unclear why the 'canned/borrowed' program was failing. I was not convinced either that we had the unit physically wired and operating correctly since the voltage readings were not as expected in certain places. So software and possible wiring issue. Hopefully some progress was made over the weekend. It was fun playing with this little thing, but it would have been nice to see it working on this night.
mlgiguere0001
Posts: 32
Joined: Wed Dec 16, 2015 2:42 pm

Re: Week #15: (4/29-5/3) Progress Reports, Inductive Prox Sensor

Post by mlgiguere0001 »

continued working on the barcode scanner using the Raspberri Pi. Also working on the card scanner, wired up the circuit for that and is functioning as should.

*discovered there are some issues with the IR sensor we were trying to use for the card scanner so opted to switch it up and make use of different sensor
Post Reply

Return to “EET-265L Lab - Evening”